Checked content

Control car (rail)

Related subjects: Railway transport

Background to the schools Wikipedia

This content from Wikipedia has been selected by SOS Children for suitability in schools around the world. A good way to help other children is by sponsoring a child

Modern German InterCity Steuerwagen cab car.
Three rail tracks 350.jpg
Rail transport
High-speed railways
Rolling stock
By country


A control car is a generic term for a non-powered railroad vehicle that can control operation of a train from the end opposite to the position of the locomotive. They can be used with diesel or electric motive power, allowing push-pull operation without the use of an additional locomotive.

Cab cars are control cars similar to regular passenger car, but with a full driver's compartment built into one or both ends. They can be very similar to regular railcars, to the point of including a gangway between cars so that they could be used in the middle of a passenger train like a regular car if necessary. They appeared for the first time in France in the 1960s.

Trains operating with a locomotive at one end and a control car at the other do not require the locomotive to run around to the opposite end of the train when reversing direction at a terminus. Control cars can carry passengers, baggage, mail or a combination thereof.

In addition to the driver's cab, which has all the controls and gauges necessary for remotely operating the locomotive, control cars usually have a horn, whistle, bell, or plough (as appropriate), and most importantly, all of the lights that would normally be on a locomotive.

Control method

In Britain, a common method is to control the train through a Time-Division Multiplexed (TDM) connection. In North America and Ireland a standard AAR 27-wire multiple unit cable with jumpers between cars is the preferred method.

North America

Some commuter rail agencies in the United States routinely use cab cars in place of regular passenger coaches on trains.

During the mid-1990s, as push-pull operations became more common in the United States, cab-cars came under criticism for providing less protection to engine crews during grade crossing accidents. This has been addressed by providing additional reinforcing in cab cars.

Amtrak non-powered control unit (NPCU) No. 90218 in Galesburg, Michigan.

Converted locomotives

From the 1970s until 1999, the Long Island Rail Road used a number of older locomotives converted to "power packs". The original prime movers were replaced with 600-horsepower engines/generators solely for supplying Head End Power or HEP with the engineer's controls left intact. Locomotives converted included Alco FA-1s, FA-2s, EMD F7s and one F9. Ontario's GO Transit had a similar program for EMD FP7s.

Amtrak developed the Non-powered Control Unit (NPCU) by removing the prime mover, main alternator, and traction motors from surplus F40 locomotives. The control cab was left in place. A floor and roll-up side-doors were then installed to allow for baggage service leading to the nickname "cab-baggage cars" or "cabbages.”


However, in Britain, this type of coach is called driving trailer and mostly this term is also used on the Continent. There are many examples of this type of vehicle in operation in Europe.



The German term for control cars is Steuerwagen.

The first German attempts to use control cars and remote control-equipped steam locomotives were before the Second World War by the Deutsche Reichsbahn (DRG). The driver's control instructions were transmitted from the control car to the locomotive by a Chadburn-type machine telegraph (similar to engine order telegraphs on ships). The order had to be immediately acknowledged and implemented by the automatic firebox controllers. This indirect control was judged as impractical and unsafe because, although the driver controlled the brake directly, the danger existed that in an emergency the locomotive would continue supplying "push" power for some time and possibly derail the train.

Attempts to use electric locomotives (beginning with a converted E 04 class model) were more promising, as the engine driver could control the locomotive directly. World War II interrupted the test program, despite good successes. Only after the war would control car operation be slowly accepted, when locomotives and suitably equipped cars became available.

The length of train consists in push-pull operations was originally limited to 10 cars for reasons of guidance dynamics. A speed limit of 120 km/h was also imposed, rising to 140 km/h in 1980. This was not an operational hindrance, as push-pull trains were generally initially used in six-car commuter trains.

Only since the mid 1990s have long-distance trains, which can have up to 14 cars and travel at speeds of 200 km/h, been operated with control cars. A special circumstance is the ICE 2, which may operate with the control car in the lead at up to 250 km/h on the recently built high-speed lines.


Iarnród Eireann operates three classes of push-pull trainsets, each with its own Control Car:

  • Mk 3 with driving cab containing replica locomotive control stand, luggage compartment, under-slung Cummins engine / generator set for train heating and passenger seating.
    • Numbered 6101 - 6105, converted from Mk 3 intercity cars for suburban push-pull service.
  • De Dietrich ( Enterprise service) with driving cab containing EMD control stand, luggage compartment and passenger seating. On this set, train heating is supplied from the locomotive Head End Power System.
    • Numbered 9001 - 9004
  • CAF ( Mk IV) with driving cab containing replica locomotive control stand, luggage compartment and twin engine / generator sets for train heating. No passenger seating is provided.
    • Numbered 4001 - 4008

All the Control Cars have full-sized driving cabs with EMD locomotive type power and brake controls. Locomotive control is by means of an AAR system, modified by Iarnród Éireann (IE) to include control of train doors and operate with IE 201 Class locomotives.


In Italy the first push-pull trains began to run after World War II.

At the time there were no systems to actually remote command the rear locomotive, so an engineer had to take place in it and command traction, following instructions (via an apposite intercom) given by the other driver, who remained in the front car, commanding brakes and sighting signals. This lasted until the adoption of the 78-wire cable in the 1970s, which enabled full remote commanding from control cars.

Today push-pull trains are very common, and different kinds of control cars are employed:

  • Uic Z1 control cars.
  • MDVC type control cars, with aerodynamic or communicating cabin.
  • Piano ribassato type control cars, with flat, refurbished E464-like or communicating cabin.
  • Doppio Piano two floors control cars.
  • UIC-X type control cars.
  • Vivalto type control car.

These types allow full remote control of any Italian locomotive supplied with standard 78-wire cable, except for UIC-X, which are used on IC services and are only able to command class E402 locomotives, and MDVC diesel specific version, usable only with Class D445 diesel locomotives.
The same driving commands are used for both rheostatic and electronic locomotives, but their meanings change.

Vivalto type control cars, at this time, can only remote command Class E464 and Class E632 locomotives, because of software issues, tough are able to command other locomotive types. Vivalto cars can also use TCN remote control cable.

Driving cars can be recognized because of the "nP" in their identification number and usually also have a dedicated compartment for bicycle and luggage transportation.

There also are specific EMU/ DMU non-motorized units control cars, which (in Trenitalia) are classified as Le XXX; no significant difference between them and motorized units, except the lack of traction motors.


Swiss driving trailers operate in many different configurations. There are several models currently in service on S-Bahn networks as well as regional, InterRegio, and InterCity services. These are operated by the federal railway system ( SBB) as well as various private railroads throughout the country (including narrow gauge lines) and into France, Germany, and Italy.

Driving trailers are classified after the UIC-lettering system, adding a "t,” giving Bt (second class), BDt (second class + baggage), ABt (first + second class), or Dt (baggage).

For Intercity trains there are the Bt IC that work together with EW IV and the double-deck version for the IC 2000 trainsets, working with Re 460.

The Zürich S-Bahn trainsets with Re 450 work in fix consists of Re 450 - B - AB - Bt but intermediate cars and driving trailers are numbered as coaching stock.

"NPZ" Regional and S-Bahn trains with RBDe 560 usually have a matching Bt driving trailer. Replacement by an older BDt EW I/II is technically possible. Older driving trailers, mostly BDt EW I/II and a few remaining Dt of SBB can be used with Re 420 and RBe 540 and some motive power of private railways. In theory also Re 430 and Re 620 can be controlled but these classes only work freight trains today.

The BLS operates four groups of driving trailers:

  • ABt NPZ to go with RBDe 565 and RBDe 566 II (ex RM)
  • ABt of a modified type EW I for RBDe 566 I (ex RM)
  • Bt EW III, BDt EW II (both ex SBB), Bt EW I 901-902 (ex Thurbo/MThB) and leased Dt from SBB can work with Re 420.5 ex SBB and BLS Re 465.
  • Bt EW I 950-953, BDt 940-941, car-shuttle BDt 942-945, 946-949 and 939 can work with Re 425, Ae 4/4 and Re 465

Südostbahn had a fleet of ABt for their BDe 4/4 but they will soon be fully replaced by FLIRTs. NPZ ABt exist for the two types of RBDe 566 SOB ownes (566 071-076 ex BT and 566 077-080 ex SOB of the SBB-type). Nine BDt are used for the Voralpen-Express with Re 456, Re 446 or SBB-CFF-FFS Re 420.

The narrow gauge Zentralbahn ABt can control HGe 101 (ex SBB), De 110, BDeh 140 (ex LSE) and the new "SPATZ" ABe 130.

The Rhaetian Railway (RhB) has, besides the ABDt that work with Be 4/4 511-516, a group of driving trailers that can be used with their Ge 4/4 I, II and III locomotives. Three of them are specially fitted for Vereina car shuttles.

The Matterhorn-Gotthard-Bahn (MGB) has numerous driving trailers for almost all types of motive power. They work regional trains and car shuttles through the Furka Tunnel.

United Kingdom

  • Driving Brake Standard Open

A Driving Brake Standard Open or DBSO is a specially converted passenger car. These have not been used on mainline passenger trains since 2006, but some are currently being refurbished for use on Network Rail test trains.

  • Driving Van Trailer

A Driving Van Trailer or DVT is a more modern type of control car, purpose-built to include space for baggage and a guard's office. The DVT was developed from the DBSO and originally designed to be used with British Rail Mark 3 and Mk 4 coaches. DVTs are in service with National Express East Coast (Mk 4), Virgin Trains and National Express East Anglia (both Mk 3).

Retrieved from ""